[. . . ] The POWER In PRESENTATION PRODUCTS DA-LITE SCREEN COMPANY, INC. Instruction Book for DESIGNER CONTOUR® ELECTROL® 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www. da-lite. com e-mail: info@da-lite. com IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. [. . . ] Remove the end cap on the right end of the case and insert the brackets into the case channel. Drill holes into the ceiling and attach screen with the appropriate fasteners for your ceiling. Do not remove the wall mount bracket, even if you are not using it for mounting. Be sure the ceiling has adequate reinforcement to attach a hook anchor. The top of the screen case has a channel that the ceiling hook brackets slide into. Remove the end cap on the right end of the case and insert the brackets into the case channel. The brackets can be attached anywhere within 12" of the end of the case. Attach an S-hook or similar fastener to the large center hole on the bracket. 2 WALL MOUNT BRACKET 4-1/4" CASE HOOK 5/16" 9/16" 4-5/8" STOP SCREW FIGURE 1 SET SCREWS (2) CEILING MOUNT HOLES ENDCAP SCREWS (3) ENDCAP FIGURE 2 SET SCREWS (2) HOOK MOUNT HOLE ENDCAP SCREWS (3) ENDCAP FIGURE 3 ELECTRICAL INSTALLATION Internal wiring has been completed at the factory. Installer must route power to the wall switch and to the junction box located on the left end of the screen case. Standard installation is for a single 120VAC or 240VAC wall switch to control the screen. Wiring diagrams for the built-in VPI and low voltage control are included in these instructions. Refer to additional instructions for the external VPI, external low voltage control, SCB-100 and SCB-200. Refer to the appropriate wiring diagram for your screen. 120V WIRING DIAGRAM FOR STANDARD WALL SWITCH JUNCTION BOX LOCATED IN LEFT ENDCAP WHITE BLACK RED GREEN MOTOR GROUND TO CASE WHITE BLACK (DOWN) RED (UP) GROUND­MUST BE CONNECTED TO BUILDING GROUND AC (COMMON) SPDT SWITCH WITH CENTER OFF BLACK UP OFF DOWN THIS SWITCH CAN NOT BE USED WITH LVC. RED AC HOT 120VAC 60HZ 1 AMP BLACK/YELLOW NOTE: A SINGLE SWITCH CANNOT BE USED TO OPERATE MORE THAN ONE SCREEN. CONTACT THE FACTORY FOR FURTHER INFORMATION. 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH: Da-Lite offers two styles of 240 volt wall switches for standard operation. Please see wiring diagram included in wall switch box included with screen. 3 ELECTRICAL INSTALLATION 120V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL RED BLACK MOTOR WHITE (COMMON) GROUND TO CASE EYE AUX BLACK WHITE RED UP STOP DOWN 120VAC 60HZ WHITE (COMMON) BLACK (HOT) GREEN LOW-VOLTAGE WALL SWITCH OPTIONAL RF OR IR REMOTE CONNECTOR GROUND­MUST BE CONNECTED TO BUILDING GROUND 240V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL BLACK (UP) BROWN (DOWN) MOTOR BLUE (COMMON) OPTIONAL RF OR IR REMOTE CONNECTOR GROUND TO CASE AUX EYE BLACK WHITE RED UP STOP BLACK DOWN 240VAC 50HZ BLUE (COMMON) BROWN (HOT) BLACK LOW-VOLTAGE WALL SWITCH GROUND­MUST BE CONNECTED TO BUILDING GROUND GREEN 4 SCREEN ADJUSTMENT Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory. [. . . ] "Up" Position Check for power across red and white leads. (b) Blown fuse. (d) No power to operating switch or junction. Power at junction box (e) Thermal overload tripped. Call for information (a) Replace motor assembly. (a) Defective brake. (a) Replace motor assembly. RESTORING LOST ROLLER WRAP 1. [. . . ]